Principles of Electricity


Series Resistance

Ohm's Law teaches us that Voltage is equal to the product of resistance and current. This is fine if we have a circuit as simple as a single light run by a battery. But how often do we truly encounter a circuit which has only one resistance? It is actually quite seldom. Most circuits have many resistances in various combinations. So we must learn how to mathematically deal with all these resistances. Fortunately, combined resistances can only be configured in two ways:
    Resistances Combined in Series
    Resistances Combined in Parallel
We will discuss each of these separately. This class is dedicated to the study of Resistances in Series, which you will find, are as simple as 2+2.

First, let us describe the difference between a SERIES circuit and a PARALLEL circuit. A SERIES circuit is hooked together like a chain, with each link connected to the link before it. If any given link in the chain is broken, the whole chain is broken, and doesn't work.

If we think of our circuit as a water pipe, a resistor could be a valve in the pipe. A series circuit would have several valves in the same pipe. If we shut the water off at any one valve, the water flow through the entire pipe would be restricted. Let's say this again another way. The flow, or current, is restricted by all the valves, but the valve with the most resistance is the one that decreases the flow the most.

Now if we draw a schematic of resistors in series, it would look like the diagram at the left. This first diagram would be an exact representation of our waterflow circuit. The tank provides a source of water, just as a battery supplies a source of electricity. The valves, which restrict the flow of water, represent the resistors, which restrict the flow of electric current.

The diagram on the right shows the equivalent circuit, with only one resistor (Rt) taking the place of all 3 resistors in the left diagram. Recall that using an electrical equivalent circuit, that ANY circuit, no matter how complex, can be represented with a single voltage source, and a single load. The question is, how do we determine the value of the TOTAL resistance when we have multiple resistors? This is the scope of this lesson. How do we mathematically combine resistances that are connected in series?


As I said before... it is as easy as 2+2. If two or more resistors are connected end to end, as in a chain, we say that they are in series. To find out the TOTAL RESISTANCE of resistors in series, all we have to do is add up their individual values. It is that simple. If we have 3 resistors, (R1, R2, and R3) each with a value of 2 Ω, the total resistance (RT) of the series circuit would be 2+2+2, or a total of 6 Ω. Hence, RT=R1+R2+R3+... is the formula for resistors combined in series.
(On The Following Indicator... PURPLE will indicate your current location)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

[COURSE INDEX] [ELECTRONICS GLOSSARY] [HOME]


Otherwise - please click to visit an advertiser so they know you saw their ad!



This Course was written by Ray Dall © All Rights Reserved.
This page and all its content Copyright, Trademarks, Intellectual Properties
and other legal issues 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011 Ray Dall.
All Rights Reserved.
And for what it's worth... this page was last updated HexDate 01-11--7D1

VISITORS:
Add Me!